LK Automation Limited
Brand:
MITSUBISHI
A1SCPU-S1 CPU unit
MITSUBISHI A1SCPU-S1 Manual And Instructions
A1SCPU-S1 datasheetPDF datasheet
A1SCPU-S1 Common InstructionsProgramming Manual
A1SCPU-S1 User's Manual
A1SCPU-S1 Dedicated InstructionsProgramming Manual
A1SCPU-S1 FundamentalsProgramming Manual
MITSUBISHI A1SCPU-S1 Product information and technical parameters：
Brand: MITSUBISHI
Name: CPU unit
Model: A1SCPU-S1
Program memory capacity: 8k.
Input / output points: maximum 256 points.
A scan cycle of PLC must pass through three stages: input sampling, program execution and output refresh.
PLC in the input sampling phase: first of all, in order to scan the sequence of all existing input latches in the input terminal of the state or input data read,
And write it into the corresponding input status register,
Refresh the input, then close the input port, enter the program execution stage.
...More relevant models >>>>
A1SCPU-S1 datasheetPDF datasheet
A1SCPU-S1 Common InstructionsProgramming Manual
A1SCPU-S1 User's Manual
A1SCPU-S1 Dedicated InstructionsProgramming Manual
A1SCPU-S1 FundamentalsProgramming Manual
MITSUBISHI A1SCPU-S1 Product information and technical parameters：
Brand: MITSUBISHI
Name: CPU unit
Model: A1SCPU-S1
Program memory capacity: 8k.
Input / output points: maximum 256 points.
A scan cycle of PLC must pass through three stages: input sampling, program execution and output refresh.
PLC in the input sampling phase: first of all, in order to scan the sequence of all existing input latches in the input terminal of the state or input data read,
And write it into the corresponding input status register,
Refresh the input, then close the input port, enter the program execution stage.
A1ST60 analog timer module has 8 analog timers.
Each timer can be set between 0.1-600S,
Its accuracy plus or minus 2%.
Dial setting on the timing constant panel of the timer,
With a small screwdriver can be easily adjusted. 8 slots; requires 1 AnS series PLC power modules;
Used to install large AnS series PLC module A1SCPU-S1.
Base plate of AnS series PLC.
QA1S series PLC 8 slot main substrate.
AnS series of modules can be installed A1SCPU-S1 Input type: AC.
Input points: 16 points.
Input voltage: AC200-240V.
Input current: 9mA.
Connection mode: terminal row.
Common common point: 16.
The instruction list programming language is a programming language similar to assembly language mnemonic,
As well as assembly language by the operation code and the number of operations A1SCPU-S1.
In the case of the computer for the PLC handheld programmer compile user program.
At the same time, the programming language of the instruction list corresponds to the ladder diagram programming language,
In PLC programming software can be converted to each other. Figure 3 is the instruction sheet corresponding to the ladder diagram of figure 2PLC A1SCPU-S1.
The characteristics of instruction table programming language is used to represent mnemonic operation function,
Easy to remember, easy to grasp;
In the handheld programmer on the keyboard using the mnemonic representation, easy to operate, can be programmed in computer;
There is a one-to-one correspondence between the ladder diagram and the ladder diagram. Its characteristics are basically consistent with the ladder diagram language. Cable length: 0.7 meters.
Extending cable to connect CPU main substrate and extended substrate,
According to the model can provide different cable length,
If you need to connect the AnN type expansion substrate is required,
Selection of A1SC05NB (A1SC07NB) cable. Input voltage: AC100-240V.
Rated output: DC5V, 5A.
The power supply module is connected with the exteernal power supply,
AnS programmable controller to provide the required DC5V,
They are inserted in the slot of the special power supply component on the base board,
The output of the DC5V is powered by the power supply on the substrate to the component A1SCPU-S1 A1SCPU-S1.
The input voltage of the component is related to the selected model.
A1S61PN/62PN has Deng generation A1S61P/A1S62P, A1S61PEU/A1S62PEU.
Each timer can be set between 0.1-600S,
Its accuracy plus or minus 2%.
Dial setting on the timing constant panel of the timer,
With a small screwdriver can be easily adjusted. 8 slots; requires 1 AnS series PLC power modules;
Used to install large AnS series PLC module A1SCPU-S1.
Base plate of AnS series PLC.
QA1S series PLC 8 slot main substrate.
AnS series of modules can be installed A1SCPU-S1 Input type: AC.
Input points: 16 points.
Input voltage: AC200-240V.
Input current: 9mA.
Connection mode: terminal row.
Common common point: 16.
The instruction list programming language is a programming language similar to assembly language mnemonic,
As well as assembly language by the operation code and the number of operations A1SCPU-S1.
In the case of the computer for the PLC handheld programmer compile user program.
At the same time, the programming language of the instruction list corresponds to the ladder diagram programming language,
In PLC programming software can be converted to each other. Figure 3 is the instruction sheet corresponding to the ladder diagram of figure 2PLC A1SCPU-S1.
The characteristics of instruction table programming language is used to represent mnemonic operation function,
Easy to remember, easy to grasp;
In the handheld programmer on the keyboard using the mnemonic representation, easy to operate, can be programmed in computer;
There is a one-to-one correspondence between the ladder diagram and the ladder diagram. Its characteristics are basically consistent with the ladder diagram language. Cable length: 0.7 meters.
Extending cable to connect CPU main substrate and extended substrate,
According to the model can provide different cable length,
If you need to connect the AnN type expansion substrate is required,
Selection of A1SC05NB (A1SC07NB) cable. Input voltage: AC100-240V.
Rated output: DC5V, 5A.
The power supply module is connected with the exteernal power supply,
AnS programmable controller to provide the required DC5V,
They are inserted in the slot of the special power supply component on the base board,
The output of the DC5V is powered by the power supply on the substrate to the component A1SCPU-S1 A1SCPU-S1.
The input voltage of the component is related to the selected model.
A1S61PN/62PN has Deng generation A1S61P/A1S62P, A1S61PEU/A1S62PEU.
...More relevant models >>>>