LK Automation Limited
Brand:
MITSUBISHI
QX11L AC input module
MITSUBISHI QX11L Manual And Instructions
QX11L datasheetPDF datasheet
QX11L datasheetPDF datasheet
QX11L User's Manual
MITSUBISHI QX11L Product information and technical parameters：
Brand: MITSUBISHI
Name: AC input module
Model: QX11L
AC input: 32 points.
Rated current and voltage: AC100 ~ 120V, 10mA (AC100V, 60Hz).
Response time: 25ms.
Input form: 1 points, 32 public ends.
External wiring connections: 38 terminals (terminals sold separately).
Replacement model: AX11.
...More relevant models >>>>
QX11L datasheetPDF datasheet
QX11L datasheetPDF datasheet
QX11L User's Manual
MITSUBISHI QX11L Product information and technical parameters：
Brand: MITSUBISHI
Name: AC input module
Model: QX11L
AC input: 32 points.
Rated current and voltage: AC100 ~ 120V, 10mA (AC100V, 60Hz).
Response time: 25ms.
Input form: 1 points, 32 public ends.
External wiring connections: 38 terminals (terminals sold separately).
Replacement model: AX11.
32 point connector for compression connector (40 pin connector.Extended SRAM card 2MB
Better user experience data recording function.
Easy to record, no need to program.
Simply through the special configuration tool wizard to easily complete the settings,
The collected data can be saved in CSV format to SD storage card QX11L.
Can be effectively used to save the CSV file to facilitate the creation of a variety of reference materials,
Including daily reports, generate reports and general reports QX11L
These data can be applied to the data analysis, tracing, etc..Master station.
Province distribution network module in cabinet and device.
Link to connect the 64 stations when the fastest scanning time for 1 QX11L. 2ms (rate 2.5Mbps).
According to the transmission distance, the transmission rate is selected from 2.5Mbps, 625kbps and 156kbps.
CC-Link/LT from the station does not need any parameter settings.
Only need to set up the transmission speed in the master module, you can use the remote I/O.
QJ61CL12 can be used as the main station of CC-Link/LT.SD memory card 16GB.
Can be used on the Q24DHCPCPU-V QX11L.
Can be used on the Q24DHCPCPU-LS.
Can be used on the QnUDVCPU.Three-phase 3 wire type.
Measuring circuit number: 1 circuits.
Measurement items: power consumption (consumption, regeneration), current, voltage, power, power factor, etc..
Power measurement module product group capable of simply measuring various energy information.
With only one module can be used to measure and power consumption (consumption and regeneration), reactive power, current, voltage, power, power factor and frequency of all kinds of detailed information.
No ladder program can continue to monitor the minimum and maximum values, can also perform 2 types of upper / lower limit alarm.
Only in the ON state can be used to measure the output of the output device.
Therefore, the amount of electricity and the quantity of electricity in the unit of the beat can be obtained during the operation of the equipment.
3 phase 3 wire products cann be used to measure up to 4 circuits in one slot,
3 phase 4 wire products can be used to measure up to 3 circuits,
So the electrical energy measurement can be carried out in a small space by the multi circuit products QX11L.
For example, a module ccan be used to measure other loads from the control panel trunk QX11L.
In addition, Works2 GX (version 1.90U and higher) can be used to easily set parameters.
Better user experience data recording function.
Easy to record, no need to program.
Simply through the special configuration tool wizard to easily complete the settings,
The collected data can be saved in CSV format to SD storage card QX11L.
Can be effectively used to save the CSV file to facilitate the creation of a variety of reference materials,
Including daily reports, generate reports and general reports QX11L
These data can be applied to the data analysis, tracing, etc..Master station.
Province distribution network module in cabinet and device.
Link to connect the 64 stations when the fastest scanning time for 1 QX11L. 2ms (rate 2.5Mbps).
According to the transmission distance, the transmission rate is selected from 2.5Mbps, 625kbps and 156kbps.
CC-Link/LT from the station does not need any parameter settings.
Only need to set up the transmission speed in the master module, you can use the remote I/O.
QJ61CL12 can be used as the main station of CC-Link/LT.SD memory card 16GB.
Can be used on the Q24DHCPCPU-V QX11L.
Can be used on the Q24DHCPCPU-LS.
Can be used on the QnUDVCPU.Three-phase 3 wire type.
Measuring circuit number: 1 circuits.
Measurement items: power consumption (consumption, regeneration), current, voltage, power, power factor, etc..
Power measurement module product group capable of simply measuring various energy information.
With only one module can be used to measure and power consumption (consumption and regeneration), reactive power, current, voltage, power, power factor and frequency of all kinds of detailed information.
No ladder program can continue to monitor the minimum and maximum values, can also perform 2 types of upper / lower limit alarm.
Only in the ON state can be used to measure the output of the output device.
Therefore, the amount of electricity and the quantity of electricity in the unit of the beat can be obtained during the operation of the equipment.
3 phase 3 wire products cann be used to measure up to 4 circuits in one slot,
3 phase 4 wire products can be used to measure up to 3 circuits,
So the electrical energy measurement can be carried out in a small space by the multi circuit products QX11L.
For example, a module ccan be used to measure other loads from the control panel trunk QX11L.
In addition, Works2 GX (version 1.90U and higher) can be used to easily set parameters.
...More relevant models >>>>