LK Automation Limited
Brand:
MITSUBISHI
Q2ASHCPU-S1 CPU unit
MITSUBISHI Q2ASHCPU-S1 Manual And Instructions
Q2ASHCPU-S1 datasheetPDF datasheet
Q2ASHCPU-S1 General Instruction Manual
Q2ASHCPU-S1 User's Manual
Q2ASHCPU-S1 HardwareUser's Manual
Q2ASHCPU-S1 User's Manual
Q2ASHCPU-S1 HardwareUser's Manual
Q2ASHCPU-S1 PID Control InstructionsProgramming Manual
MITSUBISHI Q2ASHCPU-S1 Product information and technical parameters：
Brand: MITSUBISHI
Name: CPU unit
Model: Q2ASHCPU-S1
Input and output points: 1024 points.
Input / output data points: 8192 points.
Program capacity: 60k.
Basic command processing speed (LD command) S:0.075.
PLC in the program execution stage: according to the order of the user program order to store the order of each instruction,
After the corresponding operation and processing, the result is written to the output status register,
The contents of the output status register are changed with the execution of the program.
Output refresh phase: when all instructions are executed,
The output status register is sent to the output latch in the output refresh stage,
And through a certain way (relay, transistor or transistor) output, drive the corresponding output equipment.
...More relevant models >>>>
Q2ASHCPU-S1 datasheetPDF datasheet
Q2ASHCPU-S1 General Instruction Manual
Q2ASHCPU-S1 User's Manual
Q2ASHCPU-S1 HardwareUser's Manual
Q2ASHCPU-S1 User's Manual
Q2ASHCPU-S1 HardwareUser's Manual
Q2ASHCPU-S1 PID Control InstructionsProgramming Manual
MITSUBISHI Q2ASHCPU-S1 Product information and technical parameters：
Brand: MITSUBISHI
Name: CPU unit
Model: Q2ASHCPU-S1
Input and output points: 1024 points.
Input / output data points: 8192 points.
Program capacity: 60k.
Basic command processing speed (LD command) S:0.075.
PLC in the program execution stage: according to the order of the user program order to store the order of each instruction,
After the corresponding operation and processing, the result is written to the output status register,
The contents of the output status register are changed with the execution of the program.
Output refresh phase: when all instructions are executed,
The output status register is sent to the output latch in the output refresh stage,
And through a certain way (relay, transistor or transistor) output, drive the corresponding output equipment.
Type of input: DC leakage.
Input points: 64 points.
Input voltage: DC24.
Input current: 5mA.
Connection mode: terminal row.
Common common point: 32.
Functional block diagram language is a kind of PLC programming language, which is similar to digital logic circuit.
The function module is used to represent the function of the module,
Different function modules have different functions Q2ASHCPU-S1.
Functional module figure programming language features: functional block diagram programming language is characterized by a functional module for the unit,
Analysis and understanding of the control scheme is simple and easy: function module is to use graphical form of expression,
Intuitive, for a digital logic circuit based on the design of the staff is very easy to master the programming;
Control system with complex scale and complex control logic,
Because the function module diagram can clearly express the function relation, the programming debugging time is greatly reduced Q2ASHCPU-S1 Q2ASHCPU-S1 Program memory capacity: 8k.
Input / output points: maximum 256 points.
A scan cycle of PLC must pass through three stages: input sampling, program execution and output refresh Q2ASHCPU-S1.
PLC in the input sampling phase: first of all, in order to scan the sequence of all existing input latches in the input terminal of the state or input data read,
And write it into the corresponding input status register,
Refresh the input, then close the input port, enter the program execution stage. Interface: RS232C.
Transmission distance: 15 meters.
A1SJ71UC24-R2/R4/PR computer communication components can communicate with PLC, such as computers and other external intelligent devices, and the components are as follows:
Full / half duplex transmission. Q2ASHCPU-S1.
4 special communication protocols.
No protocol and bidirectional mode.
Protocol selection switch function.
The optional baud rate, the highest 19.2K.
Since the echo diagnostic test. 8 slots; requires 1 AnS series PLC power modules;
Useed to install large AnS series PLC module Q2ASHCPU-S1.
Base plate of AnS series PLC.
QA1S series PLC 8 slot main substrate.
AnS series of modules can be installed.
Input points: 64 points.
Input voltage: DC24.
Input current: 5mA.
Connection mode: terminal row.
Common common point: 32.
Functional block diagram language is a kind of PLC programming language, which is similar to digital logic circuit.
The function module is used to represent the function of the module,
Different function modules have different functions Q2ASHCPU-S1.
Functional module figure programming language features: functional block diagram programming language is characterized by a functional module for the unit,
Analysis and understanding of the control scheme is simple and easy: function module is to use graphical form of expression,
Intuitive, for a digital logic circuit based on the design of the staff is very easy to master the programming;
Control system with complex scale and complex control logic,
Because the function module diagram can clearly express the function relation, the programming debugging time is greatly reduced Q2ASHCPU-S1 Q2ASHCPU-S1 Program memory capacity: 8k.
Input / output points: maximum 256 points.
A scan cycle of PLC must pass through three stages: input sampling, program execution and output refresh Q2ASHCPU-S1.
PLC in the input sampling phase: first of all, in order to scan the sequence of all existing input latches in the input terminal of the state or input data read,
And write it into the corresponding input status register,
Refresh the input, then close the input port, enter the program execution stage. Interface: RS232C.
Transmission distance: 15 meters.
A1SJ71UC24-R2/R4/PR computer communication components can communicate with PLC, such as computers and other external intelligent devices, and the components are as follows:
Full / half duplex transmission. Q2ASHCPU-S1.
4 special communication protocols.
No protocol and bidirectional mode.
Protocol selection switch function.
The optional baud rate, the highest 19.2K.
Since the echo diagnostic test. 8 slots; requires 1 AnS series PLC power modules;
Useed to install large AnS series PLC module Q2ASHCPU-S1.
Base plate of AnS series PLC.
QA1S series PLC 8 slot main substrate.
AnS series of modules can be installed.
...More relevant models >>>>