LK Automation Limited
Brand:
MITSUBISHI
MR-J4-70B-RJ010 Servo driver
MITSUBISHI MR-J4-70B-RJ010 Manual And Instructions
MR-J4-70B-RJ010 datasheetPDF datasheet
MITSUBISHI MR-J4-70B-RJ010 Product information and technical parameters：
Brand: MITSUBISHI
Name: Servo driver
Model: MR-J4-70B-RJ010
1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 0.75kw.
Interface: SSCNET III /H.
Power supply: three phase AC200V.
Special specification: support for CC-LinkIE.Field network motion control.
Servo amplifier supporting IE Field CC-Link network.
Ethernet based open network, support for motion control.
2 low frequency vibration can be suppressed at the same time by supporting the seismic algorithm of 3 inertial equipment.
Configurator2 MR to achieve convenient adjustment.
Effectively restrain the low frequency aftershock effect produced by the front end of the boom or the main body of the device 100Hz.
Can effectively shorten the time to control the stability of the aftershock.
In the XY design of trajectory control, improve the accuracy of arc track.
At the same time, it can effectively control the phenomenon of quadrant protrusion caused by the rotation direction of the servo motor, which is caused by friction and twisting.
...More relevant models >>>>
MR-J4-70B-RJ010 datasheetPDF datasheet
MITSUBISHI MR-J4-70B-RJ010 Product information and technical parameters：
Brand: MITSUBISHI
Name: Servo driver
Model: MR-J4-70B-RJ010
1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 0.75kw.
Interface: SSCNET III /H.
Power supply: three phase AC200V.
Special specification: support for CC-LinkIE.Field network motion control.
Servo amplifier supporting IE Field CC-Link network.
Ethernet based open network, support for motion control.
2 low frequency vibration can be suppressed at the same time by supporting the seismic algorithm of 3 inertial equipment.
Configurator2 MR to achieve convenient adjustment.
Effectively restrain the low frequency aftershock effect produced by the front end of the boom or the main body of the device 100Hz.
Can effectively shorten the time to control the stability of the aftershock.
In the XY design of trajectory control, improve the accuracy of arc track.
At the same time, it can effectively control the phenomenon of quadrant protrusion caused by the rotation direction of the servo motor, which is caused by friction and twisting.
The length of the line: 10M.
IP level: IP65.
Direct type.
Bending life: high bending life.
The cable is not shielded.
Electric motor power supply cable for HF-KP/HF-MP series (motor shaft with side extraction). Multi axis integrated servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series MR-J4-70B-RJ010.
Axis number: 2 axis.
Rated output A axis (Note 1): 0.4kw.
Rated output B axis (Note 1): 0 MR-J4-70B-RJ0104kw.
Interface: SSCNET III /H.
Note the 1:A axis, B axis, C axis indicates the name of a type of multi axis servo amplifier axis. The C axis represents the 3 axis one type servo amplifier.
Support SSCNET III /H. 1 unit can drive 2 servo motor two axis servo amplifier.
More energy saving, space saving, less wiring, low cost MR-J4-70B-RJ010.
Inherited the high performance and high reliability.
Will, as always, adhere to and uphold the excellent quality of MELSERVO.
MR-J4 has inherited the excellent design of existing products.
Its essence to its dregs, create advantage and cost effective utilization rate,
Make full use of renewable resources, to create a new product. Adapter kit (for CN3)Motor series: low inertia, small capacity MR-J4-70B-RJ010.
Using a serial absolute / incremental encoder.
Rated output power: 0.05kw.
Rated speed: 3000rpm.
With the brake: not with brake.
Without GB.
Shaft end: straight shaft.
A servo motor is an engine that controls the operation of the mechanical components in the servo system.
Servo motor can make the control speed, position accuracy is very accurate, can be converted to torque and speed voltage signals to drive the control object.
Servo motor rotor speed is controlled by the input signal, and can quickly response,
In the automatic control system, used as actuators, and electromechanicall time constant, high linearity, initiating voltage characteristics,
The signal can be converted into a motor shaft on the angular displacement or angular velocity output MR-J4-70B-RJ010.
Divided into DC and AC servo motor two major categories, the main features are,
When the signal voltage is zero, there is no rotation,
The speed increases with the increase of the torque and the speed decreases MR-J4-70B-RJ010.
IP level: IP65.
Direct type.
Bending life: high bending life.
The cable is not shielded.
Electric motor power supply cable for HF-KP/HF-MP series (motor shaft with side extraction). Multi axis integrated servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series MR-J4-70B-RJ010.
Axis number: 2 axis.
Rated output A axis (Note 1): 0.4kw.
Rated output B axis (Note 1): 0 MR-J4-70B-RJ0104kw.
Interface: SSCNET III /H.
Note the 1:A axis, B axis, C axis indicates the name of a type of multi axis servo amplifier axis. The C axis represents the 3 axis one type servo amplifier.
Support SSCNET III /H. 1 unit can drive 2 servo motor two axis servo amplifier.
More energy saving, space saving, less wiring, low cost MR-J4-70B-RJ010.
Inherited the high performance and high reliability.
Will, as always, adhere to and uphold the excellent quality of MELSERVO.
MR-J4 has inherited the excellent design of existing products.
Its essence to its dregs, create advantage and cost effective utilization rate,
Make full use of renewable resources, to create a new product. Adapter kit (for CN3)Motor series: low inertia, small capacity MR-J4-70B-RJ010.
Using a serial absolute / incremental encoder.
Rated output power: 0.05kw.
Rated speed: 3000rpm.
With the brake: not with brake.
Without GB.
Shaft end: straight shaft.
A servo motor is an engine that controls the operation of the mechanical components in the servo system.
Servo motor can make the control speed, position accuracy is very accurate, can be converted to torque and speed voltage signals to drive the control object.
Servo motor rotor speed is controlled by the input signal, and can quickly response,
In the automatic control system, used as actuators, and electromechanicall time constant, high linearity, initiating voltage characteristics,
The signal can be converted into a motor shaft on the angular displacement or angular velocity output MR-J4-70B-RJ010.
Divided into DC and AC servo motor two major categories, the main features are,
When the signal voltage is zero, there is no rotation,
The speed increases with the increase of the torque and the speed decreases MR-J4-70B-RJ010.
...More relevant models >>>>