LK Automation Limited
Brand:
MITSUBISHI
MR-J4-15KB-RJ Servo driver
MITSUBISHI MR-J4-15KB-RJ Manual And Instructions
MR-J4-15KB-RJ datasheetPDF datasheet
MITSUBISHI MR-J4-15KB-RJ Product information and technical parameters：
Brand: MITSUBISHI
Name: Servo driver
Model: MR-J4-15KB-RJ
1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 15.0kw.
Interface: SSCNET III /H.
Power supply: three phase AC200V.
Special specification: full closed loop control 4 wire / device end encoder ABZ phase input corresponding support function security unit, support positioning mode.
Servo amplifier supporting SSCNET III /H.
Complete synchronization system capable of using high speed serial optical communication.
Can be combined with the servo system controller to maximize the performance of the servo system.
The industry''s top level speed motor, the frequency of 2.5kHz amplifier, and optical fiber network extradimensional Symphony orchestra.
Using the traditional two degree of freedom model adaptive control to further optimize the exclusive high speed servo control structure of the dedicated execution engine.
Achieved the fastest 2.5kHz speed frequency response in the industry.
Combined with MITSUBISHI independent research and development of high resolution absolute position encoder (4194304pulses/rev),
Greatly improve the processing speed. Can maximize the performance of high-end machinery.
...More relevant models >>>>
MR-J4-15KB-RJ datasheetPDF datasheet
MITSUBISHI MR-J4-15KB-RJ Product information and technical parameters：
Brand: MITSUBISHI
Name: Servo driver
Model: MR-J4-15KB-RJ
1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 15.0kw.
Interface: SSCNET III /H.
Power supply: three phase AC200V.
Special specification: full closed loop control 4 wire / device end encoder ABZ phase input corresponding support function security unit, support positioning mode.
Servo amplifier supporting SSCNET III /H.
Complete synchronization system capable of using high speed serial optical communication.
Can be combined with the servo system controller to maximize the performance of the servo system.
The industry''s top level speed motor, the frequency of 2.5kHz amplifier, and optical fiber network extradimensional Symphony orchestra.
Using the traditional two degree of freedom model adaptive control to further optimize the exclusive high speed servo control structure of the dedicated execution engine.
Achieved the fastest 2.5kHz speed frequency response in the industry.
Combined with MITSUBISHI independent research and development of high resolution absolute position encoder (4194304pulses/rev),
Greatly improve the processing speed. Can maximize the performance of high-end machinery.
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.2kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: single phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller MR-J4-15KB-RJ.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication MR-J4-15KB-RJ
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data MR-J4-15KB-RJ. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operations.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient MR-J4-15KB-RJ.
The servo amplifier can be used for speed control operation.
When the two stations are occupied, the speed can be set directly by the remote register. MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 0.4kw.
SSCNET interface.
Voltage: single phase AC100V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0.888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This simple connecction method reduces the routing time and helps to prevent noise MR-J4-15KB-RJ.
Even in the MELSERVO-J2-SUPER series products using high resolution coding standards, the command frequency is no limit.
It is only necessary to add a battery on the serrvo amplifier, which can form the absolute value system MR-J4-15KB-RJ.
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use.
Rated output: 0.2kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: single phase AC200V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller MR-J4-15KB-RJ.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication MR-J4-15KB-RJ
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data MR-J4-15KB-RJ. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operations.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient MR-J4-15KB-RJ.
The servo amplifier can be used for speed control operation.
When the two stations are occupied, the speed can be set directly by the remote register. MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 0.4kw.
SSCNET interface.
Voltage: single phase AC100V.
Complete synchronization system with SSCNET high speed serial communication,
The communication cycle between the controller and the servo amplifier is the longest 0.888ms.
Such systems will be able to provide high reliability and high performance.
When connecting the servo system with SSCNET,
In the motion system, the parameters of the servo amplifier and the acquisition of the data will be displayed on the motion controller.
Connect a dedicated cable with an amplifier and a controller to form a SSCNET system.
This simple connecction method reduces the routing time and helps to prevent noise MR-J4-15KB-RJ.
Even in the MELSERVO-J2-SUPER series products using high resolution coding standards, the command frequency is no limit.
It is only necessary to add a battery on the serrvo amplifier, which can form the absolute value system MR-J4-15KB-RJ.
Currently there are more than 1000000 high reliability SSCNET servo amplifier networks in use.
...More relevant models >>>>