LK Automation Limited LK Automation Limited
Brand: MITSUBISHI
Go Back >> Product Catalogues
MR-J3-60B4-RJ006 Full closed loop control driver
MITSUBISHI MR-J3-60B4-RJ006 Manual And Instructions
MR-J3-60B4-RJ006 datasheetPDF datasheet

MITSUBISHI MR-J3-60B4-RJ006 Product information and technical parameters:
Brand: MITSUBISHI
Name: Full closed loop control driver
Model: MR-J3-60B4-RJ006
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.6kw.
Interface type: SSCNET type III fiber communication.
Full closed loop control.
Power specification: three phase AC400V.
High precision and high response location control.
Full closed loop control can be realized by double feedback control method.
Dual feedback control can be performed between the servo motor encoder and the load side encoder.
MR-J3-B-RJ006 can be used in conjunction with a number of manufacturers of linear encoder,
Users can build the system according to their own accuracy requirements. ABS type linear encoder using serial interface,
No need to install the battery on the servo amplifier can easily build the absolute position detection system.
Flexible system configuration.
Can achieve higher load side positioning accuracy!

Drive: MR-H_ACN series CC-LINK features.
Rated output: 15KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions MR-J3-60B4-RJ006.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data MR-J3-60B4-RJ006 Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive MR-J3-60B4-RJ006.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive. Motor: HA-SH type.
Power: 7.0kw.
Speed: 2000r/min MR-J3-60B4-RJ006.
The speed regulating motor can be divided into a constant speed motor, a stepless constant speed motor, a stepless speed changing motor and a stepless speed changing motor,
Can also be divided into electromagnetic induction motor, DC motor, PWM variable frequency motor and switched reluctance motor.
The rotor speed of the induction motor is always slightly lower than that of the rotating magnetic field.
The rotor speed of the synchronous motor is not independent of the load size, but is always maintained as a synchronous speed. Motor series: low inertia, medium and small capacity.
Using a serial absolute / incremental encoder.
Rated output power: 0.1kw.
Rated speed: 3000rpm.
With a brake band.
Shaft end: straight shaft.
Comparison of single phase induction motor and servo motor.
The working principle of the AC servo motor is similar to that of the single phase induction motor,
But the rotor resistance of the former is much larger than that of the latter,
So the servo motor is compared with the single machine asynchronous motor,
There are three notable features:
1, large starting torque.
2, a wide rangge of operation MR-J3-60B4-RJ006.
3, no rotation phenomenon.
AC servo motor running smoothly, low noise.
But the control characteristic is non-linear, and because the rotor resistance is big, the loss is big, the efficiency is low,
Therefore, comparred with the same capacity DC servo motor, the volume is large and the weight is heavy,
So it is only suitable for 0 MR-J3-60B4-RJ006. 5-100W small power control system.


...More relevant models >>>>