LK Automation Limited
Brand:
MITSUBISHI
MR-H60TN Servo amplifier
MITSUBISHI MR-H60TN Manual And Instructions
MR-H60TN datasheetPDF datasheet
MR-H60TN Instruction manual
MITSUBISHI MR-H60TN Product information and technical parameters：
Brand: MITSUBISHI
Name: Servo amplifier
Model: MR-H60TN
Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.6KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive.
...More relevant models >>>>
MR-H60TN datasheetPDF datasheet
MR-H60TN Instruction manual
MITSUBISHI MR-H60TN Product information and technical parameters：
Brand: MITSUBISHI
Name: Servo amplifier
Model: MR-H60TN
Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.6KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive.
The length of the line: 10M.
IP level: IP65.
Cable outlet direction: the same side of the motor shaft.
Bending life: high bending life.
Encoder with cable (motor side); for HF-KP/HF-MP series (motor shaft with side extraction). Servo motor series: low inertia, medium / high power.
Rated output: 15.0kw MR-H60TN.
Rated speed: 1000r/min.
Electromagnetic brake: No.
Shaft end specification: Standard (straight axis) MR-H60TN
Voltage: 400V level.
Features: low inertia has low medium and high speed three models, suitable for different applications as a standard, 30KW and above servo motor can be installed flange or bracket.
IP level: IP44.
Application example:
1, injection molding machine.
2, semiconductor manufacturing equipment MR-H60TN.
3, large material handling system.
4, stamping machine.
Abundant motor product line can optimize the performance of the machine.
Has a rich motor product line including a rotary servo motor, linear servo motor and direct drive motor. Drive: MR-H_ACN series SSC-NET compatible AC servo.
Rated output: 7.0KW.
The servo controller can easily transfer the operation module and the field bus module through the automation interface,
At the same time using different fieldbus modules to achieve different control modes (RS485, RS232, optical fiber, InterBus, ProfiBus),
And the control mode of general inverter is single MR-H60TN.
The servo controller is directly connected with a rotary transformer or an encoder, which forms a closed loop of speed and displacement control.
The general inverter can only form an open loop control system.
Servo controller of the control parameters (such as steady-state accuracy and dynamic performance) is better than the general inverter. Type: general purpose AC servo amplifier MR-E series.
Rated output: 0.1kw.
Interface type: general purpose pulse interface.
KH003 special mark for Super MR-E.
High performance and easy to operate, reduce work load.
Enhanced system cost performance.
High performmance, high precision positioning (servo motor encoder resolution: 131072) MR-H60TN.
High response.
Suppression of vibration by adaptive vibration suppression control.
Using personal computer and servo setup software to optimize tuning.
Has 2 types of interfaces:
Position control and speed control with pulse train interface MR-H60TN.
The analog input interface is used for speed control and torque control.
IP level: IP65.
Cable outlet direction: the same side of the motor shaft.
Bending life: high bending life.
Encoder with cable (motor side); for HF-KP/HF-MP series (motor shaft with side extraction). Servo motor series: low inertia, medium / high power.
Rated output: 15.0kw MR-H60TN.
Rated speed: 1000r/min.
Electromagnetic brake: No.
Shaft end specification: Standard (straight axis) MR-H60TN
Voltage: 400V level.
Features: low inertia has low medium and high speed three models, suitable for different applications as a standard, 30KW and above servo motor can be installed flange or bracket.
IP level: IP44.
Application example:
1, injection molding machine.
2, semiconductor manufacturing equipment MR-H60TN.
3, large material handling system.
4, stamping machine.
Abundant motor product line can optimize the performance of the machine.
Has a rich motor product line including a rotary servo motor, linear servo motor and direct drive motor. Drive: MR-H_ACN series SSC-NET compatible AC servo.
Rated output: 7.0KW.
The servo controller can easily transfer the operation module and the field bus module through the automation interface,
At the same time using different fieldbus modules to achieve different control modes (RS485, RS232, optical fiber, InterBus, ProfiBus),
And the control mode of general inverter is single MR-H60TN.
The servo controller is directly connected with a rotary transformer or an encoder, which forms a closed loop of speed and displacement control.
The general inverter can only form an open loop control system.
Servo controller of the control parameters (such as steady-state accuracy and dynamic performance) is better than the general inverter. Type: general purpose AC servo amplifier MR-E series.
Rated output: 0.1kw.
Interface type: general purpose pulse interface.
KH003 special mark for Super MR-E.
High performance and easy to operate, reduce work load.
Enhanced system cost performance.
High performmance, high precision positioning (servo motor encoder resolution: 131072) MR-H60TN.
High response.
Suppression of vibration by adaptive vibration suppression control.
Using personal computer and servo setup software to optimize tuning.
Has 2 types of interfaces:
Position control and speed control with pulse train interface MR-H60TN.
The analog input interface is used for speed control and torque control.
...More relevant models >>>>