LK Automation Limited
Brand:
MITSUBISHI
MM-EFS30K1M4 IPM motor
MITSUBISHI MM-EFS30K1M4 Manual And Instructions
MM-EFS30K1M4 datasheetPDF datasheet
MITSUBISHI MM-EFS30K1M4 Product information and technical parameters：
Brand: MITSUBISHI
Name: IPM motor
Model: MM-EFS30K1M4
Superior high efficiency IPM motor.
Output power: 30kw.
Rated speed: 1500r/min.
Voltage level: 400V.
IPM motor MM-EFS series can not be used to run the power frequency power.
The total wiring length of the IPM motor shall not exceed 100m.
1 inverters can not connect multiple IPM motors at the same time.
...More relevant models >>>>
MM-EFS30K1M4 datasheetPDF datasheet
MITSUBISHI MM-EFS30K1M4 Product information and technical parameters：
Brand: MITSUBISHI
Name: IPM motor
Model: MM-EFS30K1M4
Superior high efficiency IPM motor.
Output power: 30kw.
Rated speed: 1500r/min.
Voltage level: 400V.
IPM motor MM-EFS series can not be used to run the power frequency power.
The total wiring length of the IPM motor shall not exceed 100m.
1 inverters can not connect multiple IPM motors at the same time.
MITSUBISHI inverter series: FR-F820.
Voltage level: three phase 200V.
Power: 75kw.
SLD converter rated current: 380A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have.
PID target value can be set directly from the operator panel. Flexible change settings.
In the 1 inverter, through the PID control of parallel connection pump (up to 4 units) can adjust the amount of water and so on MM-EFS30K1M4 MM-EFS30K1M4
1 pumps driven by parallel connection of the pump machine, in addition to the pump for power frequency drive.
The number of power frequency driven pump, according to the automatic adjustment of water.
The liquid crystal panel options (FR-LU08) can be converted to a more intuitive display unit% units MM-EFS30K1M4.
Through the use of wind, temperature and other familiar units can be simple to maintain and adjust the display. Power: 75kw.
Voltage: 200V.
The power factor of the input power factor is up to 0.99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function. Power: 280kw.
Voltage: 400V.
The power factor of the input power factor is up to 0 MM-EFS30K1M4. 99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function. MITSUBISHI inverter series: FR-F840.
Voltage level: three phase 400V.
Power: 7.5kw.
SLD converter rated current: 17.0A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have.
2 times the power consumption of the wind turbine and pump and the speed of the 3 power consumption is proportional to the speed of the rotating speed.
Through the speed control of the frequency converter to adjust the air flow, can reduce the power cconsumption MM-EFS30K1M4.
Give full play to the performance of the motor.
The excitation current is always adjusted to the best state, which can improve the efficiency of the motor.
Load torque is smaller, can further improve energy efficiency.
For example, when a general motor is used, the optimal excitation control mode in the 4% motor load torque is about 30% more than that of the V/F control MM-EFS30K1M4.
Voltage level: three phase 200V.
Power: 75kw.
SLD converter rated current: 380A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have.
PID target value can be set directly from the operator panel. Flexible change settings.
In the 1 inverter, through the PID control of parallel connection pump (up to 4 units) can adjust the amount of water and so on MM-EFS30K1M4 MM-EFS30K1M4
1 pumps driven by parallel connection of the pump machine, in addition to the pump for power frequency drive.
The number of power frequency driven pump, according to the automatic adjustment of water.
The liquid crystal panel options (FR-LU08) can be converted to a more intuitive display unit% units MM-EFS30K1M4.
Through the use of wind, temperature and other familiar units can be simple to maintain and adjust the display. Power: 75kw.
Voltage: 200V.
The power factor of the input power factor is up to 0.99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function. Power: 280kw.
Voltage: 400V.
The power factor of the input power factor is up to 0 MM-EFS30K1M4. 99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function. MITSUBISHI inverter series: FR-F840.
Voltage level: three phase 400V.
Power: 7.5kw.
SLD converter rated current: 17.0A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have.
2 times the power consumption of the wind turbine and pump and the speed of the 3 power consumption is proportional to the speed of the rotating speed.
Through the speed control of the frequency converter to adjust the air flow, can reduce the power cconsumption MM-EFS30K1M4.
Give full play to the performance of the motor.
The excitation current is always adjusted to the best state, which can improve the efficiency of the motor.
Load torque is smaller, can further improve energy efficiency.
For example, when a general motor is used, the optimal excitation control mode in the 4% motor load torque is about 30% more than that of the V/F control MM-EFS30K1M4.
...More relevant models >>>>