LK Automation Limited
Brand:
MITSUBISHI
HC-SF121 Medium inertia medium capacity motor
MITSUBISHI HC-SF121 Manual And Instructions
HC-SF121 datasheetPDF datasheet
MITSUBISHI HC-SF121 Product information and technical parameters：
Brand: MITSUBISHI
Name: Medium inertia medium capacity motor
Model: HC-SF121
Motor series: medium inertia, medium capacity.
Using a serial absolute / incremental encoder.
Rated output power: 1.2kw.
Rated speed: 1000rpm.
With the brake: without.
Shaft end: straight shaft.
The structure of the AC servo motor stator is basically similar to the capacitor split phase single-phase induction motor.
The stator is provided with two positions of 90 degrees of mutual difference of the winding, one is the excitation winding Rf, it is always connected to the AC voltage Uf;
The other is to control the winding L, which is connected to the control signal voltage Uc.
So the AC servo motor, also known as the two servo motor.
...More relevant models >>>>
HC-SF121 datasheetPDF datasheet
MITSUBISHI HC-SF121 Product information and technical parameters：
Brand: MITSUBISHI
Name: Medium inertia medium capacity motor
Model: HC-SF121
Motor series: medium inertia, medium capacity.
Using a serial absolute / incremental encoder.
Rated output power: 1.2kw.
Rated speed: 1000rpm.
With the brake: without.
Shaft end: straight shaft.
The structure of the AC servo motor stator is basically similar to the capacitor split phase single-phase induction motor.
The stator is provided with two positions of 90 degrees of mutual difference of the winding, one is the excitation winding Rf, it is always connected to the AC voltage Uf;
The other is to control the winding L, which is connected to the control signal voltage Uc.
So the AC servo motor, also known as the two servo motor.
Cable length: 1.0M.
Amplifier CC-Link interface unit cable.
For MR-J2S-11KA (4) MR-J2S-22KA to (4). MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 0.2kw.
Built in positioning function.
Voltage: single phase AC100V.
Compatible with "MR-J2S- CP-S084" - servo amplifier and interface unit "MR-J2S-TO1" positioning by CC-Link
Simply setting the point table HC-SF121 HC-SF121
AC servo can be used as the driving source of the field network.
Using servo amplifier built-in positioning function, position data and speed data, you can set the CC-Link.
Start, stop and display can also be transmitted through the CC-Link.
Serial communication reduces wiring.
AC servo distributed control system can be easily constructed HC-SF121. Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.6KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data HC-SF121. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3W series (a two axis servo amplifier).
Rated output A axis: 1.0kw.
Rated output B axis: 1.0kw.
Interface type: SSCNET type III fiber communication.
With the same high performance, multi functionality and practicality of the MR-J3-B servo amplifier,
Each MR-J3W-B servo amplifier can be used to rotate the servo motor,
Combined controll of any two kinds of linear servo motor and direct drive servo motor HC-SF121.
The installation area can be reduced by 25% to 17% compared with two MR-J3-B servo amplifiers.
Therefore, a more compact control system can be constructed.
In addition, the two axes use the same main circuit power supply, control circuit power supply and SSCNET III communication fiber, thus greatly reducing the wiring HC-SF121.
Amplifier CC-Link interface unit cable.
For MR-J2S-11KA (4) MR-J2S-22KA to (4). MITSUBISHI general purpose AC servo amplifier MELSERVO-J2-Super series.
Rated output: 0.2kw.
Built in positioning function.
Voltage: single phase AC100V.
Compatible with "MR-J2S- CP-S084" - servo amplifier and interface unit "MR-J2S-TO1" positioning by CC-Link
Simply setting the point table HC-SF121 HC-SF121
AC servo can be used as the driving source of the field network.
Using servo amplifier built-in positioning function, position data and speed data, you can set the CC-Link.
Start, stop and display can also be transmitted through the CC-Link.
Serial communication reduces wiring.
AC servo distributed control system can be easily constructed HC-SF121. Drive: MR-H_ACN series CC-LINK features.
Rated output: 0.6KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data HC-SF121. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3W series (a two axis servo amplifier).
Rated output A axis: 1.0kw.
Rated output B axis: 1.0kw.
Interface type: SSCNET type III fiber communication.
With the same high performance, multi functionality and practicality of the MR-J3-B servo amplifier,
Each MR-J3W-B servo amplifier can be used to rotate the servo motor,
Combined controll of any two kinds of linear servo motor and direct drive servo motor HC-SF121.
The installation area can be reduced by 25% to 17% compared with two MR-J3-B servo amplifiers.
Therefore, a more compact control system can be constructed.
In addition, the two axes use the same main circuit power supply, control circuit power supply and SSCNET III communication fiber, thus greatly reducing the wiring HC-SF121.
...More relevant models >>>>