LK Automation Limited LK Automation Limited
Brand: MITSUBISHI
Go Back >> Product Catalogues
GT1675M-STBD 10.4 inch touch screen
MITSUBISHI GT1675M-STBD Manual And Instructions
GT1675M-STBD datasheetPDF datasheet
GT1675M-STBD User's Manual
GT1675M-STBD MES Interface Function Manual
GT1675M-STBD Gateway Functions Manual
GT1675M-STBD Extended/Option Functions Manual
GT1675M-STBD Mitsubishi plc ConnectionsConnection Manual
GT1675M-STBD Connection Manual

MITSUBISHI GT1675M-STBD Product information and technical parameters:
Brand: MITSUBISHI
Name: 10.4 inch touch screen
Model: GT1675M-STBD
Series: multimedia and advanced features and features of a variety of high-performance models.
Screen size: 10.4 inches.
Display color: 256 color or more color.
Installation type: compatible with multimedia and video /RGB.
Resolution: SVGA (800 x 600).
Display device: TFT color (high brightness, wide viewing angle).
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422.
High performance models with multimedia and advanced features and functionality (including embedded communications capabilities).
User storage capacity: 15MB (GT16__-VNB__:11MB).
With HOST USB and device USB port.
Standard Ethernet, RS-422/485 and RS-232 ports.
Support multimedia and video /RGB units.
Analog touch panel.
Do not let the touch screen surface with water drops or other soft things stick to the surface,
Otherwise, the touch screen is easy to mistake that there is a hand touch caused by surface acoustic wave screen is not allowed.
In addition to cleaning the dirt on the surface of the touch screen,
You can use a soft dry cloth or a cleaning agent to clean out the center of the screen carefully,
Or use a dry soft cloth dipped in industrial alcohol or glass cleaning fluid to clean the touch screen surface.
Touch screen response is slow if you use a hand or other touch to touch the surface acoustic wave touch screen,
This shows that it is likely that the touch screen system has been obsolete, the internal clock frequency is too low,
Or because there is water in the surface of the touch screen to make the touch screen mobile, rapid response recovery,
To replace or upgrade the system must, or use dry cloth touch screen on the surface of the water.
If the user is operating the touch screen, the direction of the touch move is to the left,
But the cursor of the system moves to the right,
The failure may be due to the connection of the control box and the touch screen connected to the connector or the touch screen,
Users as long as the direction of the re exchange of it.

A series of high performance models that are widely used in network or single machine work environments.
Screen size: 10.4 inches.
Display color: 256 color or more color.
Installation type: compatible with video /RGB.
Resolution: SVGA (800 x 600).
Display device: TFT color (high brightness, wide viewing angle) GT1675M-STBD.
Host frame color: black.
Power type: DC24V.
Communication interface: with built-in RS-422 GT1675M-STBD
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system GT1675M-STBD.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly GT1675M-STBD. For the GT1665M-VTB.
Applicable model: GT16. For GT1575V-STB / /GT1575-VTB / /GT1575-STB.
Applicable model: GT15. "No extended memory.
Applicable model: GT15. Connecting cable for handheld RH GOT and PLC.
Cable length: 3 meters.
Application: RS-422 connection and RS-232C connection. Cable length: 30 meters.
For connection between GOT and CRT. Protective film for 3.7 inch screen.
Scrub (frame: white), 5.
Applicable model: GT1020. Function: high performance and low price in the middle end model.
Picture size: 8.4 inches.
Resolution: VGA.
Display: TFT color.
Panel color: black.
Power type: AC100~240V.
The highest level model with multi touch and gesture features.
Specification rich, design at ease.
GT27 standard supports SD memory card and standard equipped with Ethernet, RS-232, RS-422/485, host/device USB interface.
Even in the log, script, alarm, soft component data transmission, such as high load processing period, but also to achieve smooth operation of the screen.
In addition, also supports video, animation playback, video input and RGB input and output, can use all the features of GOT2000.
Can be programmed CPU and other procedures, parameters, such as data storage (backup) to the SD GOT memory card, USB memory.
When the programmable controller fails, batch write back (recovery) program.
1, the human body sensor
People will be able to automatically detect and display the picture.
2, USB interface: device USB (Mini-B USB)
Can connect to the computer to transfer data.
3, USB interface: host USB (USB-A)
GOT data can be transmitted through the USB memory or read log data and other data,
Can also be connected to the USB mouse, keyboard use.
4, the extension of the interface
Communication module andd optional module can be installed GT1675M-STBD.
5, Ethernet interface
Up to 4 different manufacturers can be connected to the FA machine.
6, RS-232 interface
Can connect all kinds of FA machine, bar code reader, serial printer.
7, RS-422/485 interfface
Can be connected to a variety of FA machines, bar code reader GT1675M-STBD.
8, SD memory card slot
Can save alarm and log data, such as a large number of data.


...More relevant models >>>>