LK Automation Limited
Brand:
MITSUBISHI
FX3U-ENET-ADP Special adapter for connecting Ethernet
MITSUBISHI FX3U-ENET-ADP Manual And Instructions
FX3U-ENET-ADP datasheetPDF datasheet
FX3U-ENET-ADP INSTALLATION MANUAL
FX3U-ENET-ADP User's Manual
MITSUBISHI FX3U-ENET-ADP Product information and technical parameters：
Brand: MITSUBISHI
Name: Special adapter for connecting Ethernet
Model: FX3U-ENET-ADP
Protocol: SLMP, TCP/IP, UDP, SNTP.
Communication mode: full duplex / half duplex.
At the same time can open a few: 4 connection.
Weight: 0.3kg.
Can be low cost will be connected to the FX3 series Ethernet.
Support data monitoring, can monitor the basic unit through the computer browser,
Remote maintenance can be carried out by Works2 GX in a place far from the scene.
Connect FX3SA, FX3S, FX3GA, FX3G, FX3U host, you need to convert the adapter or function expansion board.
...More relevant models >>>>
FX3U-ENET-ADP datasheetPDF datasheet
FX3U-ENET-ADP INSTALLATION MANUAL
FX3U-ENET-ADP User's Manual
MITSUBISHI FX3U-ENET-ADP Product information and technical parameters：
Brand: MITSUBISHI
Name: Special adapter for connecting Ethernet
Model: FX3U-ENET-ADP
Protocol: SLMP, TCP/IP, UDP, SNTP.
Communication mode: full duplex / half duplex.
At the same time can open a few: 4 connection.
Weight: 0.3kg.
Can be low cost will be connected to the FX3 series Ethernet.
Support data monitoring, can monitor the basic unit through the computer browser,
Remote maintenance can be carried out by Works2 GX in a place far from the scene.
Connect FX3SA, FX3S, FX3GA, FX3G, FX3U host, you need to convert the adapter or function expansion board.
Input and output points: 48 points.
DC power supply: DC24V.
Input points: 24 points.
Output points: 24 points.
Output form: relay output.
Weight: 0.85kg.
Input signal voltage: DC24V.
FX2N series expansion unit
Expansion unit is an input and output expansion device with a built-in power supply.
As with the basic unit, the extension unit can be connected to a variety of input and output and special extension equipment FX3U-ENET-ADP FX3U-ENET-ADP
Can connect to FX3GA/FX3G, FX3GE and FX3U.
AC power model, the built-in maximum DC24V 250mA/460mA supply power.
Because all models of FX series are built in high speed counter,
So the high speed control can be realized by the simple procedure.
The input of the basic unit is built in the anti jitter filter,
One part as digital filter,
Sensitivity adjustment unit can reach 1ms FX3U-ENET-ADP.
Using high speed counter automatically adjusted to the minimum value.
Through the high cost of the built-in positioning function and the expansion function to increase the number of control axis.
Extended function expansion board and special adapter,
Data links and communication with external serial devices FX3U-ENET-ADP. Length: 55mm.
Function: connect GM-FX.
Corresponding models: FX2N-10GM, FX2N-20GM. 8 point analog potentiometer function expansion board.Memory format: RAM.
Number of steps: up to 16000 steps can be used.
Battery support: required.
Method for writing and deleting: the device is installed on the PLC, and is written and deleted by the peripheral device. RS-232C communication adapter.
(need FX1N-CNV-BD).
(FX1S and FX1N host general). Axis of control: 1.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
7 operating modules required for eeasy positioning control are provided FX3U-ENET-ADP.
Type of instruction, please refer to the list in front of you.
One can control a shaft.
FX3U, PLC FX2N can connect up to 8 units,
PLC FX2NC can connect up to 4 units,
PLC FX3UC can connect up to 77 units, so that it can control more than one independent axis FX3U-ENET-ADP.
Maximum can output 100kHz pulse train.
Positioning control through the control program.
DC power supply: DC24V.
Input points: 24 points.
Output points: 24 points.
Output form: relay output.
Weight: 0.85kg.
Input signal voltage: DC24V.
FX2N series expansion unit
Expansion unit is an input and output expansion device with a built-in power supply.
As with the basic unit, the extension unit can be connected to a variety of input and output and special extension equipment FX3U-ENET-ADP FX3U-ENET-ADP
Can connect to FX3GA/FX3G, FX3GE and FX3U.
AC power model, the built-in maximum DC24V 250mA/460mA supply power.
Because all models of FX series are built in high speed counter,
So the high speed control can be realized by the simple procedure.
The input of the basic unit is built in the anti jitter filter,
One part as digital filter,
Sensitivity adjustment unit can reach 1ms FX3U-ENET-ADP.
Using high speed counter automatically adjusted to the minimum value.
Through the high cost of the built-in positioning function and the expansion function to increase the number of control axis.
Extended function expansion board and special adapter,
Data links and communication with external serial devices FX3U-ENET-ADP. Length: 55mm.
Function: connect GM-FX.
Corresponding models: FX2N-10GM, FX2N-20GM. 8 point analog potentiometer function expansion board.Memory format: RAM.
Number of steps: up to 16000 steps can be used.
Battery support: required.
Method for writing and deleting: the device is installed on the PLC, and is written and deleted by the peripheral device. RS-232C communication adapter.
(need FX1N-CNV-BD).
(FX1S and FX1N host general). Axis of control: 1.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V).
7 operating modules required for eeasy positioning control are provided FX3U-ENET-ADP.
Type of instruction, please refer to the list in front of you.
One can control a shaft.
FX3U, PLC FX2N can connect up to 8 units,
PLC FX2NC can connect up to 4 units,
PLC FX3UC can connect up to 77 units, so that it can control more than one independent axis FX3U-ENET-ADP.
Maximum can output 100kHz pulse train.
Positioning control through the control program.
...More relevant models >>>>