LK Automation Limited
Brand:
MITSUBISHI
FX2N-32CCL CC-Link interface module
MITSUBISHI FX2N-32CCL Manual And Instructions
FX2N-32CCL datasheetPDF datasheet
FX2N-32CCL User's Manual
FX2N-32CCL User's Manual
MITSUBISHI FX2N-32CCL Product information and technical parameters：
Brand: MITSUBISHI
Name: CC-Link interface module
Model: FX2N-32CCL
CC-Link interface module.
PLC FX can be used as the CC-LINK remote device station connection.
If using CC-LINK type FX2N-16CCL-M system master module,
So just PLC CC-LINK can build FX system.
...More relevant models >>>>
FX2N-32CCL datasheetPDF datasheet
FX2N-32CCL User's Manual
FX2N-32CCL User's Manual
MITSUBISHI FX2N-32CCL Product information and technical parameters：
Brand: MITSUBISHI
Name: CC-Link interface module
Model: FX2N-32CCL
CC-Link interface module.
PLC FX can be used as the CC-LINK remote device station connection.
If using CC-LINK type FX2N-16CCL-M system master module,
So just PLC CC-LINK can build FX system.
Needle number: 20.
Specification: loose wire connector, 5 sets (0.3mm 2). Voltage input: DC0~10V, DC0~5V.
Current input: DC4~20mA.
Voltage output: DC0~10V, DC0~5V.
Current output: DC4~20mA.
Applicable PLC:FX1N, FX2N, FX1NC, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V) FX2N-32CCL.
8 bit binary resolution analog input and output modules.
Input output mixed module with 2 channel analog input and 1 channel analog output FX2N-32CCL
Voltage input and current input of 2 channels can be carried out.
1 channel analog output can be the output voltage or current output. Axis of control: 1.
Instruction speed: 1Hz~1MHz.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V) FX2N-32CCL.
The maximum 1MHz high speed pulse, can carry on the high speed, high precision positioning.
Can be in the range of 1Hz to 1Hz~1MHz as the interval output pulse.
The high speed moving time can be shortened to 1ms by using a dedicated start input.
Enhanced speed control function.
Support the approximate S type of acceleration and deceleration function, form operation function, through the maximum 30kHz of the external input pulse rate of synchronization operation, etc FX2N-32CCL. . Input points: 32 points.
Connected programmable logic controller: FX1NC, FX2NC, FX3UC.
Weight: 0.2KG.
FX2NC expansion module can be directly connected to the FX1NC, FX2NC, PLC FX3UC on the expansion of the input and output.
Do not need to connect the cable and so on, therefore can carry on the compact expansion. Cable flat cable;
Connector with 20 pin installed at both ends of the fuse.
Length 1.5M. Memory type: EEPROM.
Protection switch: have.
Program transfer function.
EEPROM memory can be connected to FX3SA,, FX3GA, FX3GE do not need a battery backup and with the program transfer function FX2N-32CCL.
Protective switch with incidental write protection,
Program transfer function between built-in PLC and memory box.
When the memory box is installed on thee PLC host, the program in the memory box is preferred FX2N-32CCL.
The memory box can be installed on the function expansion board and FX3S-CNV-ADP, FX3G-CNV-ADP.
Specification: loose wire connector, 5 sets (0.3mm 2). Voltage input: DC0~10V, DC0~5V.
Current input: DC4~20mA.
Voltage output: DC0~10V, DC0~5V.
Current output: DC4~20mA.
Applicable PLC:FX1N, FX2N, FX1NC, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V) FX2N-32CCL.
8 bit binary resolution analog input and output modules.
Input output mixed module with 2 channel analog input and 1 channel analog output FX2N-32CCL
Voltage input and current input of 2 channels can be carried out.
1 channel analog output can be the output voltage or current output. Axis of control: 1.
Instruction speed: 1Hz~1MHz.
Applicable PLC:FX1N, FX2N, FX3U, FX2NC (to FX2NC-CNV-IF).
Applicable PLC:FX3UC (to FX2NC-CNV-IF or FX3UC-1PS-5V) FX2N-32CCL.
The maximum 1MHz high speed pulse, can carry on the high speed, high precision positioning.
Can be in the range of 1Hz to 1Hz~1MHz as the interval output pulse.
The high speed moving time can be shortened to 1ms by using a dedicated start input.
Enhanced speed control function.
Support the approximate S type of acceleration and deceleration function, form operation function, through the maximum 30kHz of the external input pulse rate of synchronization operation, etc FX2N-32CCL. . Input points: 32 points.
Connected programmable logic controller: FX1NC, FX2NC, FX3UC.
Weight: 0.2KG.
FX2NC expansion module can be directly connected to the FX1NC, FX2NC, PLC FX3UC on the expansion of the input and output.
Do not need to connect the cable and so on, therefore can carry on the compact expansion. Cable flat cable;
Connector with 20 pin installed at both ends of the fuse.
Length 1.5M. Memory type: EEPROM.
Protection switch: have.
Program transfer function.
EEPROM memory can be connected to FX3SA,, FX3GA, FX3GE do not need a battery backup and with the program transfer function FX2N-32CCL.
Protective switch with incidental write protection,
Program transfer function between built-in PLC and memory box.
When the memory box is installed on thee PLC host, the program in the memory box is preferred FX2N-32CCL.
The memory box can be installed on the function expansion board and FX3S-CNV-ADP, FX3G-CNV-ADP.
...More relevant models >>>>