LK Automation Limited
Brand:
MITSUBISHI
FR-HC2-H400K hpfr
MITSUBISHI FR-HC2-H400K Manual And Instructions
FR-HC2-H400K datasheetPDF datasheet
MITSUBISHI FR-HC2-H400K Product information and technical parameters：
Brand: MITSUBISHI
Name: hpfr
Model: FR-HC2-H400K
Power: 400kw.
Voltage: 400V.
The power factor of the input power factor is up to 0.99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function.
...More relevant models >>>>
FR-HC2-H400K datasheetPDF datasheet
MITSUBISHI FR-HC2-H400K Product information and technical parameters：
Brand: MITSUBISHI
Name: hpfr
Model: FR-HC2-H400K
Power: 400kw.
Voltage: 400V.
The power factor of the input power factor is up to 0.99 and above (100% load).
Can be connected to multiple inverters, to achieve a common DC bus mode.
Equipped with standard power retrogradation function.
Power: 30kw.
Purpose: to suppress the power harmonics.
Improve the power factor, reduce the input side of the high harmonic current.
Make sure that this option is installed in the FR-A820-03800 (75K) and FR-A840-02160 (75K) and above capacity and above capacity.
At the same time the installation options in the use of 75kW and above motor FR-HC2-H400K. (the IP55 series has a built-in DC reactor.)
According to the motor power used to select the DC reactor FR-HC2-H400K
(when the inverter capacity is greater than the motor capacity, is still based on the motor capacity to choose.) MITSUBISHI inverter FR-F720 series.
Voltage level: three phase 200V.
Frequency converter capacity: 45KW.
When the ring is opened, the frequency converter is provided with a load of the motor when the motor is operated with a load at a given frequency,
The range of the motor speed in the rated slip ratio (1%~5%) changes FR-HC2-H400K.
For the requirements of relatively high precision, even if the load changes are also required to operate at a given speed of the occasion,
Inverter with PG feedback function can be used (selection).
If the given acceleration time is too short, the output frequency of the inverter is far more than the change of the speed (electric angular frequency),
Converter will be due to flow over the current trip, the operation stopped, which is called stall FR-HC2-H400K. Superior high efficiency IPM motor.
Output power: 37kw.
Rated speed: 1500r/min.
Voltage level: 400V.
IPM motor MM-EFS series can not be used to run the power frequency power.
The total wiring length of the IPM motor shall not exceed 100m.
1 inverters can not connect multiple IPM motors at the same time. Power: 110kw.
Voltage: 200V.
Sine wave filter.
The voltage and current of the motor can be adjustted to a sine wave FR-HC2-H400K.
The sine wave filter is installed to the output terminal of the inverter.
Applicable to FR-A820-03800 (75K) above and FR-A840-02160 (75K) and above frequency converter.
Sine wave filter is equivalent to the operationnal characteristics of the sine wave power driver, can provide the following benefits FR-HC2-H400K.
Low noise.
No surge current.
Reduce motor loss (standard motor).
Purpose: to suppress the power harmonics.
Improve the power factor, reduce the input side of the high harmonic current.
Make sure that this option is installed in the FR-A820-03800 (75K) and FR-A840-02160 (75K) and above capacity and above capacity.
At the same time the installation options in the use of 75kW and above motor FR-HC2-H400K. (the IP55 series has a built-in DC reactor.)
According to the motor power used to select the DC reactor FR-HC2-H400K
(when the inverter capacity is greater than the motor capacity, is still based on the motor capacity to choose.) MITSUBISHI inverter FR-F720 series.
Voltage level: three phase 200V.
Frequency converter capacity: 45KW.
When the ring is opened, the frequency converter is provided with a load of the motor when the motor is operated with a load at a given frequency,
The range of the motor speed in the rated slip ratio (1%~5%) changes FR-HC2-H400K.
For the requirements of relatively high precision, even if the load changes are also required to operate at a given speed of the occasion,
Inverter with PG feedback function can be used (selection).
If the given acceleration time is too short, the output frequency of the inverter is far more than the change of the speed (electric angular frequency),
Converter will be due to flow over the current trip, the operation stopped, which is called stall FR-HC2-H400K. Superior high efficiency IPM motor.
Output power: 37kw.
Rated speed: 1500r/min.
Voltage level: 400V.
IPM motor MM-EFS series can not be used to run the power frequency power.
The total wiring length of the IPM motor shall not exceed 100m.
1 inverters can not connect multiple IPM motors at the same time. Power: 110kw.
Voltage: 200V.
Sine wave filter.
The voltage and current of the motor can be adjustted to a sine wave FR-HC2-H400K.
The sine wave filter is installed to the output terminal of the inverter.
Applicable to FR-A820-03800 (75K) above and FR-A840-02160 (75K) and above frequency converter.
Sine wave filter is equivalent to the operationnal characteristics of the sine wave power driver, can provide the following benefits FR-HC2-H400K.
Low noise.
No surge current.
Reduce motor loss (standard motor).
...More relevant models >>>>