LK Automation Limited
Brand:
MITSUBISHI
FR-ABR-H0.75K High frequency braking resistor
MITSUBISHI FR-ABR-H0.75K Manual And Instructions
FR-ABR-H0.75K datasheetPDF datasheet
FR-ABR-H0.75K Instruction manual
MITSUBISHI FR-ABR-H0.75K Product information and technical parameters：
Brand: MITSUBISHI
Name: High frequency braking resistor
Model: FR-ABR-H0.75K
Power: 0.75kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table.
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling.
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor.
The installation of thermal relay, to avoid overheating and burn the braking resistor.
...More relevant models >>>>
FR-ABR-H0.75K datasheetPDF datasheet
FR-ABR-H0.75K Instruction manual
MITSUBISHI FR-ABR-H0.75K Product information and technical parameters：
Brand: MITSUBISHI
Name: High frequency braking resistor
Model: FR-ABR-H0.75K
Power: 0.75kw.
Purpose: high frequency braking resistor.
The use rate of the built-in regenerative brake of the transducer can be promoted.
When using the FR-ABR type brake resistor, the short circuit piece between the terminal PR-PX is removed. Does not remove the short circuit chip will lead to overheating of the brake resistor.
The utilization rate of the regenerative braking should be less than the allowable brake use rate in the above table.
With the operating frequency of the brake resistor to reach 300 degrees C or higher, it is necessary to take protective measures and cooling.
MYS type resistor can be used. But please pay attention to the allowable brake use rate.
Do not remove the terminal P/+ and P1 between the short circuit chip, in addition to connecting the DC reactor.
The installation of thermal relay, to avoid overheating and burn the braking resistor.
MITSUBISHI inverter FR-L740 series.
Voltage level: three phase 400V.
Frequency converter capacity: 22KW.
Integration of the three works the core technology, the outstanding performance of reeling, release the high cost of bright light.
Wide range of professional use and advanced control.
Professional built-in function to ensure the constant material tension, suitable for the application of printing and packaging industry FR-ABR-H0 FR-ABR-H0.75K75K.
Fusion application of the tension products of MITSUBISHI by inverter.
Suitable for tension control of high precision cable and material processing occasions.
Professional function to ensure the safe operation of textile machinery equipment,
The spinning quality and production efficiency are improved FR-ABR-H0.75K. The application of textile machinery and equipment. Power: 37kw.
Voltage: 200V.
There are 100% braking torque output in continuous regeneration, which can correspond to the continuous regeneration operation of the pipeline control.
There is no need to install the braking unit for each frequency converter, which can reduce the comprehensive space and reduce the comprehensive cost FR-ABR-H0.75K.
Renewable energy can be used for other frequency converter, excess energy back to the grid, to achieve energy saving. Superior high efficiency IPM motor.
Output power: 5.5kw.
Rated speed: 1500r/min.
Voltage level: 200V.
IPM motor MM-EFS series can not be used to run the power frequency power.
The total wiring length of the IPM motor shall not exceed 100m.
1 inverters can not connect multiple IPM motors at the same time. MITSUBISHI inverter series: FR-F842.
Voltage level: three phase 400V.
Power: 450kw.
SLD converter rated current: 962A.
Structure and function: the rectification part is off type.
Type: CA.
Substrate coating: have.
Energy saving by high efficiency motor.
Reduce standby power consumption.
DC24V external power supply, the input MC signal can be stopped after the motor for the OFF, in the motor drive for the ON.
Standby power management can be carried out by means of frequency converter to realize the power cconsumption reduction of standby time FR-ABR-H0.75K.
According to the temperature of the inverter cooling fan, the operation of the inverter can be controlled.
According to the operating conditions of the inverter cooling fan output the correspondinng signal,
Therefore, the inverter and other built-in fan and inverter cooling fan synchronous operation FR-ABR-H0.75K.
Can reduce the power consumption in the stop.
Voltage level: three phase 400V.
Frequency converter capacity: 22KW.
Integration of the three works the core technology, the outstanding performance of reeling, release the high cost of bright light.
Wide range of professional use and advanced control.
Professional built-in function to ensure the constant material tension, suitable for the application of printing and packaging industry FR-ABR-H0 FR-ABR-H0.75K75K.
Fusion application of the tension products of MITSUBISHI by inverter.
Suitable for tension control of high precision cable and material processing occasions.
Professional function to ensure the safe operation of textile machinery equipment,
The spinning quality and production efficiency are improved FR-ABR-H0.75K. The application of textile machinery and equipment. Power: 37kw.
Voltage: 200V.
There are 100% braking torque output in continuous regeneration, which can correspond to the continuous regeneration operation of the pipeline control.
There is no need to install the braking unit for each frequency converter, which can reduce the comprehensive space and reduce the comprehensive cost FR-ABR-H0.75K.
Renewable energy can be used for other frequency converter, excess energy back to the grid, to achieve energy saving. Superior high efficiency IPM motor.
Output power: 5.5kw.
Rated speed: 1500r/min.
Voltage level: 200V.
IPM motor MM-EFS series can not be used to run the power frequency power.
The total wiring length of the IPM motor shall not exceed 100m.
1 inverters can not connect multiple IPM motors at the same time. MITSUBISHI inverter series: FR-F842.
Voltage level: three phase 400V.
Power: 450kw.
SLD converter rated current: 962A.
Structure and function: the rectification part is off type.
Type: CA.
Substrate coating: have.
Energy saving by high efficiency motor.
Reduce standby power consumption.
DC24V external power supply, the input MC signal can be stopped after the motor for the OFF, in the motor drive for the ON.
Standby power management can be carried out by means of frequency converter to realize the power cconsumption reduction of standby time FR-ABR-H0.75K.
According to the temperature of the inverter cooling fan, the operation of the inverter can be controlled.
According to the operating conditions of the inverter cooling fan output the correspondinng signal,
Therefore, the inverter and other built-in fan and inverter cooling fan synchronous operation FR-ABR-H0.75K.
Can reduce the power consumption in the stop.
...More relevant models >>>>