LK Automation Limited
Brand:
MITSUBISHI
F9GT-40UMB Picture data transfer board
MITSUBISHI F9GT-40UMB Product information and technical parameters：
Brand: MITSUBISHI
Name: Picture data transfer board
Model: F9GT-40UMB
Application: you can transfer the same image data at a high speed (about two seconds per 64KB data) to multiple F940GOT.
When programming software is used in the case of Designer2 GT,
You can create a file in HEX Intel format.
Using communication software to transfer data to a ROM writer.
Application Series: F940GOT.
Parallel printer connection (1CH).
Applicable models: A95_ (-M3) /A956WGOT. Series: multimedia and advanced features and features of a variety of high-performance models.
Screen size: 6.5 inches.
Display color: 256 color or more color.
Installation type: hand held.
Resolution: VGA (640 x 480).
Display device: TFT color (high brightness, wide viewing angle) F9GT-40UMB.
Host frame color: black.
Power type: DC24V F9GT-40UMB
Communication interface: with built-in RS-422.
High performance models with multimedia and advanced features and functionality (including embedded communications capabilities).
User storage capacity: 15MB (GT16__-VNB__:11MB).
With HOST USB and device USB port.
Standard Ethernet, RS-422/485 and RS-232 ports F9GT-40UMB.
Support multimedia and video /RGB units.
Analog touch panel.
Do not let the touch screen surface with water drops or other soft things stick to the surface,
Otherwise, the touch screen is easy to mistake that there is a hand touch caused by surface acoustic wave screen is not allowed.
In addition to cleaning the dirt on the surface of the touch screen,
You can use a soft dry cloth or a cleaning agent to clean out the center of the screen carefully,
Or use a dry soft cloth dipped in industrial alcohol or glass cleaning fluid to clean the touch screen surface F9GT-40UMB.
Touch screen response is slow if you use a hand or other touch to touch the surface acoustic wave touch screen,
This shows that it is likely that the touch screen system has been obsolete, the internal clock frequency is too low,
Or because there is water in the surface of the touch screen to make the touch screen mobile, rapid response recovery,
To replace or upgrade the system musst, or use dry cloth touch screen on the surface of the water F9GT-40UMB.
If the user is operating the touch screen, the direction of the touch move is to the left,
But the cursor of the system moves to the right,
The failure may be due to the conneection of the control box and the touch screen connected to the connector or the touch screen,
Users as long as the direction of the re exchange of it F9GT-40UMB.
Applicable models: A95_ (-M3) /A956WGOT. Series: multimedia and advanced features and features of a variety of high-performance models.
Screen size: 6.5 inches.
Display color: 256 color or more color.
Installation type: hand held.
Resolution: VGA (640 x 480).
Display device: TFT color (high brightness, wide viewing angle) F9GT-40UMB.
Host frame color: black.
Power type: DC24V F9GT-40UMB
Communication interface: with built-in RS-422.
High performance models with multimedia and advanced features and functionality (including embedded communications capabilities).
User storage capacity: 15MB (GT16__-VNB__:11MB).
With HOST USB and device USB port.
Standard Ethernet, RS-422/485 and RS-232 ports F9GT-40UMB.
Support multimedia and video /RGB units.
Analog touch panel.
Do not let the touch screen surface with water drops or other soft things stick to the surface,
Otherwise, the touch screen is easy to mistake that there is a hand touch caused by surface acoustic wave screen is not allowed.
In addition to cleaning the dirt on the surface of the touch screen,
You can use a soft dry cloth or a cleaning agent to clean out the center of the screen carefully,
Or use a dry soft cloth dipped in industrial alcohol or glass cleaning fluid to clean the touch screen surface F9GT-40UMB.
Touch screen response is slow if you use a hand or other touch to touch the surface acoustic wave touch screen,
This shows that it is likely that the touch screen system has been obsolete, the internal clock frequency is too low,
Or because there is water in the surface of the touch screen to make the touch screen mobile, rapid response recovery,
To replace or upgrade the system musst, or use dry cloth touch screen on the surface of the water F9GT-40UMB.
If the user is operating the touch screen, the direction of the touch move is to the left,
But the cursor of the system moves to the right,
The failure may be due to the conneection of the control box and the touch screen connected to the connector or the touch screen,
Users as long as the direction of the re exchange of it F9GT-40UMB.
...More relevant models >>>>
Related download