LK Automation Limited LK Automation Limited
Brand Sort: MITSUBISHI
Home >> Price
MITSUBISHI Q64DA Price
  • Brand: MITSUBISHI
  • Country: JAPAN
  • Name: Voltage / current output analog module (old model)
  • Model: Q64DA
  • Price: U.S.$ 1110.17
MITSUBISHI Q64DA
1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 2.0kw.
Interface: SSCNET III /H.
Power supply: three phase AC400V.
0.6kW and 1kW above the servo amplifier.
Servo amplifier supporting SSCNET III /H.
Complete synchronization system capable of using high speed serial optical communication.
Can be combined with the servo system controller to maximize the performance of the servo system Q64DA
2 low frequency vibration can be suppressed at the same time by supporting the seismic algorithm of 3 inertial equipment.
Configurator2 MR to achieve convenient adjustment.
Effectively restrain the low frequency aftershock effect produced by the front end of the boom or the main body of the device 100Hz.
Can effectively shorten the time to control the stability of the aftershock.
In the XY design of trajectory control, improve the accuracy of arc track.
At the same time, it can effectively control the phenomenon of quadrant protrusion caused by the rotation direction of the servo motor, which is caused by friction and twisting. Oil resistant cap for 12.1 inch screen.
Applicable model: GT16. Fiber length: 5 meters.
SSCNET III cables (external standard optical fiber control cabinet).
Joints for CN1A and CN1B. Station type: Master station.
Maximum number of stations: maximum 16.
Occupied points: 8 points.
Transfer speed: 10Mbps.
Power supply: 240mA DC24V.
Weight: 0.3kg.
FX3U-16CCL-M is the master module of V2 CC-LINK.
The main station can be connected to 8 remote I/O stations, and 8 remote equipment station or intelligent equipment station.
Can be connected to FX3GA, FX3GE, FX3GC, FX3U and FX3UC of the host.
Connecting FX3UC, FX3GC requires FX2NC-CNV-IF or FX3UC-IPS-5V. A series of high performance models that are widely used in network or single machine work environments.
Screen size: 10.4 inches.
Display color: 256 color or more color.
Mounting type: panel mounting type.
Resolution: SVGA (800 x 600).
Display device: TFT color (high brightness, wide viewing angle).
Host frame color: black.
Power type: AC100~240V.
Communication interface: with built-in RS-422.
Ideal model for high performance in a network or independent operation environment.
User storage capacity: 9MB (GT15__-VNB_:5MB).
Device USB port.
Standard RS-232 interface.
Support video /RGB unit.
If the capacitive touch screen is in the middle of the operation, the display resolution or display mode of the touch screen is changed again,
Or the refresh rate of the touch screen controller is adjusted by itself, and the cursor and the touch point can not be felt when the cursor is not corresponding to the touch point,
Must be re calibrated to the touch screen system.
In order to ensure the normal operation of the touch screen system, in addition to ensure the proper installation of the system software,
Must also remember that in a host do not install two or more than two kinds of touch screen driver,
This will cause the system to run in conflict, so that the touch screen system can not be used properly.
Q64DA Operation manual/Instructions/Model selection sample download link: /searchDownload.html?Search=Q64DA&select=5


...more relevant model market price >>>>
Related products
MITSUBISHI
5.7 Inch Touch Screen
GT1155-QTBDA
MITSUBISHI 5.7 Inch Touch Screen GT1155-QTBDA
"Series introduction: with a variety of
MITSUBISHI
Analog output module
FX2N-2DA
MITSUBISHI Analog output module FX2N-2DA
Voltage input: DC010V, DC05V. Current
MITSUBISHI
Current output analog module
Q68DAIN
MITSUBISHI Current output analog module Q68DAIN
Output: 8 channels. Input resolution:
MITSUBISHI
Redundant power module
Q64RP
MITSUBISHI Redundant power module Q64RP
Input voltage range: AC100-120V/AC200-24